[ncl-talk] issue with resP at gsnMaximize in the Panel plots and 2nd label bar
Geeta Geeta
geetag54 at yahoo.com
Wed Aug 26 10:52:48 MDT 2020
thanks Mr Brownrigg.
Sorry for the typo. I did not notice it. The warning message has gone but plot size is the same.
Geeta.
On Wednesday, 26 August, 2020, 06:46:29 pm IST, Rick Brownrigg <brownrig at ucar.edu> wrote:
Hi,
The resource errors are due to a typo -- it should be tiMainOn.
I'm not sure about the sizing.
Rick
On Wed, Aug 26, 2020 at 3:47 AM Geeta Geeta via ncl-talk <ncl-talk at mailman.ucar.edu> wrote:
Thanks Mr Phillips.
I did as you had told me to.
1. commented the draw and frame lines and added those Resources to the panel plots. and rescommon at tiMain = False
but got warning message. warning:tiMain is not a valid resource in wind_contour at this time
warning:tiMain is not a valid resource in map at this time
warning:tiMain is not a valid resource in wind_vector at this time
warning:tiMain is not a valid resource in wind_vector at this time
warning:tiMain is not a valid resource in wind_vector at this time
warning:tiMain is not a valid resource in wind_contour at this time
warning:tiMain is not a valid resource in wind_contour at this time
warning:tiMain is not a valid resource in wind_contour at this time
warning:tiMain is not a valid resource in wind_contour at this time
warning:tiMain is not a valid resource in map at this time
2. No of Plots are now =4.
But the size of plot remains the same. These are overlay plots which I am panelling.
PLOT = new(4,graphic)
gsn_panel(wks,PLOT,(/4,1/),resP)
thanks once again. I am attaching the figure so obtained.
Geeta.
On Tuesday, 25 August, 2020, 09:13:40 pm IST, Adam Phillips <asphilli at ucar.edu> wrote:
Hi Geeta,It looks like you are drawing each individual plot and then advancing the frame before your call gsn_panel:draw(PLOT(3))
frame(wks)
remove all of the draw(PLOT lines and the frame(wks) lines. I am surprised you are not getting an error message when you are doing this as you are trying to draw the same plot twice.
Assuming you corrected the definition of PLOT to be of size 4, there are a few other steps you can take to try to minimize the space between the panels (and therefore increase the size of each panel).Try setting these:
rescommon at tiMainOn = False ; turn off main title; do not save space for main titleresP at gsnPanelYWhiteSpacePercent = 0.0 ; set the amount of Y-axis space between the panels equal to 0.
Hope that helps!Adam
On Mon, Aug 24, 2020 at 10:32 PM Geeta Geeta <geetag54 at yahoo.com> wrote:
Thank you Mr Phillips.
I will try with label bar resources.
I also wanted know why the plots are so small. when I have set resP at gsnMaximize = True ; maximize plots in the panel plot resources.
what I should do to make them cover the entire page.
Geeta.
On Monday, 24 August, 2020, 09:57:49 pm IST, Adam Phillips <asphilli at ucar.edu> wrote:
Hi Geeta,1 - You are getting the error message because PLOT was defined like this:PLOT = new(5,graphic)
but then 4 plots were specified in your call to gsn_panel:gsn_panel(wks,PLOT,(/4,1/),resP)
Set PLOT = new(4,graphic) and the error will disappear.
2 - If you set cnFillOn = False, NCL will not draw a labelbar even if you set lbLabelBarOn = True. You will need to use gsn_labelbar_ndc or gsn_create_labelbar. I prefer gsn_labelbar_ndc unless you need to attach a labelbar to a plot. See the examples at the bottom of the gsn_labelbar_ndc documentation page, specifically the first example, for how to use this procedure.
3 - There are numerous ways to alter the labelbar, most of which are shown in the labelbar applications page here: http://www.ncl.ucar.edu/Applications/labelbar.shtml
Hope that helps!Adam
On Mon, Aug 24, 2020 at 5:39 AM Geeta Geeta via ncl-talk <ncl-talk at mailman.ucar.edu> wrote:
Hi
I am making panel plots with 4 rows and 1 column.
I have set following resources in the PANEL plots
resP = True
resP at gsnMaximize = True ; maximize plots
resP at gsnPanelLabelBar = True
resP at lbOrientation = "Vertical"
So 1st problem is panel plots are very small. this is the error coming. I have defined 4 rows and 1 columns and the no pf PLOTS=4
then why this warning message is coming
(0) Warning: gsn_panel: you have more plots than you have panels.
(0) Only 4 plots will be drawn.
2. The second label bar wrt the Q contour is not shown.
3. How can I adjust the two label bars. (one for filled contours and other for the line)
kindly suggest.
Geeta._______________________________________________
ncl-talk mailing list
ncl-talk at mailman.ucar.edu
List instructions, subscriber options, unsubscribe:
https://mailman.ucar.edu/mailman/listinfo/ncl-talk
--
Adam Phillips
Associate Scientist, Climate and Global Dynamics Laboratory, NCAR
www.cgd.ucar.edu/staff/asphilli/ 303-497-1726
--
Adam Phillips
Associate Scientist, Climate and Global Dynamics Laboratory, NCAR
www.cgd.ucar.edu/staff/asphilli/ 303-497-1726_______________________________________________
ncl-talk mailing list
ncl-talk at mailman.ucar.edu
List instructions, subscriber options, unsubscribe:
https://mailman.ucar.edu/mailman/listinfo/ncl-talk
More information about the ncl-talk
mailing list