[ncl-install] Fwd: NCL INSTALLING

[Abdoulaye SY]

---------- Forwarded message ----------
From: Abdoulaye SY <sy.abdoulaye3 at ugb.edu.sn>
Date: 2014-06-08 18:12 GMT+00:00
Subject: Re: [ncl-install] NCL INSTALLING
To: Mary Haley <haley at ucar.edu>


Hi,

I have download *ncl_arg-6.0.2.Linux_Debian6.0_i686_gcc445.tar.gz *and i
have done steps on http://www.ncl.ucar.edu/Download/install.shtml and when
i test the installation with

*ng4ex gsun01n -clean*

i get this message

" NCAR Graphics NCL Example <gsun01n>


This example was set up to display the output to an
X11 window.

  Copying gsun01n.ncl

Running NCL...
ncl: error while loading shared libraries: libcrypto.so.0.9.8: cannot open
shared object file: No such file or directory

ncl failed. "

and with this command



*ncargex cpex08 -clean
*i get the following error message

*"* NCAR Graphics Fortran  Example <cpex08>

  Copying cpex08.f

  Copying cpexcc.f

Compiling and linking...
gfortran -fPIC -fno-second-underscore -fno-range-check -fopenmp -O -o
cpex08 cpexcc.f cpex08.f -L/usr/local/ncl-6.2.0/lib -L/usr/X11R6/lib64
-lncarg -lncarg_gks -lncarg_c -lX11 -lXext -lcairo -lfontconfig
-lpixman-1 -lfreetype -lexpat -lpng -lz -liconv -lXrender -lbz2

gfortran: Command not found.

The compile and link failed.
*"*

What is the problem?

Thanks


2014-06-03 15:00 GMT+00:00 Mary Haley <haley at ucar.edu>:


> Hi,
>
> I recommend that you install NCL from a pre-built LINUX binary, rather
> than trying to build it from source code.
>
> We don't have binaries specifically for Ubuntu, but the Debian binaries
> should work.
>
> To download NCL using a pre-built LINUX binary, first look at:
>
> http://www.ncl.ucar.edu/Download/install.shtml
>
> and then this will help you determine which LINUX binary to download:
>
> http://www.ncl.ucar.edu/Download/linux.shtml
>
> Good luck,
>
> --Mary
>
>
> On Jun 2, 2014, at 12:53 PM, Abdoulaye SY <sy.abdoulaye3 at ugb.edu.sn>
> wrote:
>
> > Hello,
> >
> > I want to install ncl_ncarg-6.1.2 on my ubuntu (Linux 86_64 GNU/Linux)
> > I use the installation guide (INSTALL.html)
> > But when i do :
> > make -f Makefile.ini
> >
> > I have:  make: Nothing to be done for `all'.
> > And
> >  ./ymake -config `pwd`
> > I have:  bash: ./ymake: /bin/csh: bad interpreter: No such file or
> directory
> >
> >
> >
> > Then I want to know the problem and the solution
> >
> > And i want to know how to modify ymake file and set up configuration
> file for my Operating System
> >
> > Thanks
> > _______________________________________________
> > ncl-install mailing list
> > List instructions, subscriber options, unsubscribe:
> > http://mailman.ucar.edu/mailman/listinfo/ncl-install
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://mailman.ucar.edu/pipermail/ncl-install/attachments/20140608/f5d179d9/attachment.html