[ncl-install] NCL Installation failure in Ubuntu 18.04

[Suma Bhanu Battula]

Hi Kevin,

Yes, you're right. I think instructions on the website worked well for me.
It's just that there's some problem in running the test scripts. Maybe you
should edit them. Other scripts are working fine. I'm new to NCL and so
couldn't figure out what was wrong.

Thanks and Regards,
Suma



[image: Mailtrack]
<https://mailtrack.io?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality5&>
Sender
notified by
Mailtrack
<https://mailtrack.io?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality5&>
06/07/18,
8:03:50 AM

On Wed, Jun 6, 2018 at 7:19 PM, Kevin Hallock <hallock at ucar.edu> wrote:

> Hi Suma,
>
> If you’re seeing the “ncl 0>” prompt after running the ncl command, then
> it seems like NCL is working. Were the issues you had in your original
> email only encountered when trying to use pre-compiled binaries, or did the
> same errors occur with the “software center” version?
>
> If you continue to experience errors, could you please run the command “env
> | grep NCARG” and reply with the output? This will print all of the
> NCL-related environment variables that are set for your shell environment,
> which are occasionally set incorrectly by default on Ubuntu.
>
> I hope this helps,
> Kevin
>
> On Jun 5, 2018, at 11:23 PM, Suma Bhanu Battula <
> sumabhanubattula05 at gmail.com> wrote:
>
>
> Hi Kevin,
>
> I actually tried installing both 'ncl_ncarg-6.4.0-Debian7.11_64bit_gnu472.tar.gz'
> and “ncl_ncarg-6.4.0-Debian8.6_64bit_gnu492.tar.gz”. Also I tried both
> OPeNDAP binaries and non-OPeNDAP binaries of version 6.4.0. But nothing
> worked well for me. Also, Ubuntu 18.04 has NCL V 6.4.0 inbuilt in its
> software centre. But after installation, when you run through the terminal,
> it shows something like this.
>
> Copyright (C) 1995-2017 - All Rights Reserved
>  University Corporation for Atmospheric Research
>  NCAR Command Language Version 6.4.0
>  The use of this software is governed by a License Agreement.
>  See http://www.ncl.ucar.edu/ for more details.
> ncl 0>
>
> Thanks,
> Suma
>
>
>
> [image: Mailtrack]
> <https://mailtrack.io/?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality5&> Sender
> notified by
> Mailtrack
> <https://mailtrack.io/?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality5&> 06/06/18,
> 9:53:01 PM
>
> On Wed, Jun 6, 2018 at 2:42 AM, Kevin Hallock <hallock at ucar.edu> wrote:
>
>> Hi Suma,
>>
>> Which of the pre-compiled binaries did you install? Ubuntu 18.04 is very
>> new and we haven’t tested it with any of our existing binaries, so I’m not
>> sure if any of them would actually be compatible. Of the available binary
>> tarballs, I think that “ncl_ncarg-6.4.0-Debian8.6_64bit_gnu492.tar.gz”
>> is most likely to be compatible with your system.
>>
>> Also, could you please try running “ncl -V”?
>>
>> Thanks,
>> Kevin
>>
>> On Jun 5, 2018, at 2:30 AM, Suma Bhanu Battula via ncl-install <
>> ncl-install at ucar.edu> wrote:
>>
>> Dear Sir/Mam,
>>
>> I tried to Install NCL on  Ubuntu 18.04 from the pre-compiled binaries
>> available on the NCAR website. I worked according to the instruction given
>> for Linux installation. Though everything seemed to be fine, in the end I
>> could not run ncl.
>>
>> I attach the error statement I encoutered
>>
>> suma at suma:~$ ncl -x xy01n.ncl
>>  Copyright (C) 1995-2017 - All Rights Reserved
>>  University Corporation for Atmospheric Research
>>  NCAR Command Language Version 6.4.0
>>  The use of this software is governed by a License Agreement.
>>  See http://www.ncl.ucar.edu/ for more details.
>> fatal: can't find file "xy01n.ncl"
>>
>> suma at suma:~$ ng4ex xy01n -clean
>>
>> NCAR Graphics NCL Example <xy01n>
>>
>> Segmentation fault (core dumped)
>>   Copying xy01n.ncl
>> cp: cannot stat '/usr/local/ncl-6.4.0/lib/ncarg/nclex//xy01n.ncl': No
>> such file or directory
>>
>> Running NCL...
>> xy01n.ncl: No such file or directory.
>>
>> ncl failed.
>>
>> suma at suma:~$ ncargex cpex08 -clean
>>
>> NCAR Graphics Fortran  Example <cpex08>
>>
>>   Copying cpex08.f
>>
>>   Copying cpexcc.f
>>
>> Compiling and linking...
>> gfortran -fPIC -fno-second-underscore -fno-range-check -fopenmp -O -o
>> cpex08 cpexcc.f cpex08.f -L/usr/local/ncl-6.4.0/lib -L/usr/X11R6/lib64
>> -lncarg -lncarg_gks -lncarg_c -lX11 -lXext -lcairo -lfontconfig -lpixman-1
>> -lfreetype -lexpat -lpng -lz -lpthread -lXrender -lbz2
>> Segmentation fault (core dumped)
>>
>> The compile and link failed.
>>
>> Kindly help me with what could be done to run NCL 6.4.0
>>
>> Thanks and regards.
>> Suma
>>
>>
>>
>>
>>
>>
>>
>> [image: Mailtrack]
>> <https://mailtrack.io/?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality5&> Sender
>> notified by
>> Mailtrack
>> <https://mailtrack.io/?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality5&> 06/06/18,
>> 12:59:03 AM
>> _______________________________________________
>> ncl-install mailing list
>> List instructions, subscriber options, unsubscribe:
>> http://mailman.ucar.edu/mailman/listinfo/ncl-install
>>
>>
>>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mailman.ucar.edu/pipermail/ncl-install/attachments/20180606/5f49c6e5/attachment.html>