[Met_help] [rt.rap.ucar.edu #86400] History for Fwd: METv7 questions
Julie Prestopnik via RT
met_help at ucar.edu
Wed Aug 1 11:09:15 MDT 2018
----------------------------------------------------------------
Initial Request
----------------------------------------------------------------
---------- Forwarded message ---------
From: Yu Xin <learnerxy at 163.com>
Date: Mon, Jul 30, 2018 at 4:15 PM
Subject: METv7 questions
To: John Halley Gotway <johnhg at ucar.edu>
To whom that is concerned,
I have some questions about METv7 to ask.Could you please give me your
hands on it? See the below.
I am looking forward to your news and thank you so much.
With my best regards,
Yu
在 2018-07-31 04:22:22，"John Halley Gotway" <johnhg at ucar.edu> 写道：
Hi Yu,
I’m out of the office this week. Please send this message to
met_help at ucar.edu and hopefully my colleagues can answer your question.
Thanks
John
On Mon, Jul 30, 2018 at 1:55 PM Yu Xin <learnerxy at 163.com> wrote:
> Hello John Halley,
>
> These days, I have been trying to update our operational METv4.0 to
> METv7.0, but failed on it. The main problems are as follows up to now:
>
> 1) How should I configure the Config file of precipitation evaluation? I
> set it like these referring to the REAME file:
>
> fcst = {
>
> field = [
>
>
> {
>
> name = "APCP";
>
> level = [ "A06" ];
>
> cat_thresh = [ >=0.1, >=2.5,>=3.8, >=5.0, >=7.5,>=10.0,>=15.0,
> >=20.0, >=40.0 ];
>
> }
>
>
> ];
>
>
> }
>
>
> obs = fcst;
>
>
>
> but after executing it, it will remind that the name of APCPA06 is
> unrecognized, like these:
> DEBUG 2: Reading data for *APCPA06*.
>
> WARNING: process_fcst_climo_files() -> no fields matching *APCPA06* found
> in file:
> /glade/work/yuxin/met/MET-result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061800
>
> DEBUG 2: Reading data for *APCPA06*.
>
> WARNING: process_fcst_climo_files() -> no fields matching *APCPA06* found
> in file:
> /glade/work/yuxin/met/MET-result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061800
>
> DEBUG 2: Reading data for *APCPA06*.
>
> WARNING: process_fcst_climo_files() -> no fields matching *APCPA06* found
> in file:
> /glade/work/yuxin/met/MET-result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061806
>
> So I don't know how to set the precipitation variable correctly in the
> corresponding file in METv7.0.
>
> 2) I am puzzled by the SATOB's message type in METv7.0. The corresponding
> input file is little_r format and I set it in the config file like these:
>
> fcst = {
>
> field = [
>
>
> {
>
> name = "WIND";
>
> level = [
> "P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> ];
>
> cat_thresh = [ >0.0 ];
>
> },
>
>
> {
>
> name = "UGRD";
>
> level = [
> "P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> ];
>
> cat_thresh = [ >0.0 ];
>
> },
>
>
> {
>
> name = "VGRD";
>
> level = [
> "P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> ];
>
> cat_thresh = [ >0.0 ];
>
> },
>
>
> {
>
> name = "HGT";
>
> level = [
> "P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> ];
>
> cat_thresh = [ >0.0 ];
>
> }
>
>
> ];
>
>
> }
>
> obs = fcst;
>
> //
>
> // Point observation filtering options
>
> // May be set separately in each "obs.field" entry
>
> //
>
> message_type = [ "SATWND" ];
>
> sid_exc = [];
>
> obs_quality = [];
>
> duplicate_flag = NONE;
>
> obs_summary = NONE;
>
> obs_perc_value = 50;
>
>
> //
>
> // Mapping of message type group name to comma-separated list of values.
>
> //
>
> message_type_group_map = [
>
> { key = "SURFACE"; val = "ADPSFC,SFCSHP,MSONET"; },
>
> { key = "ANYAIR"; val = "AIRCAR,AIRCFT"; },
>
> { key = "ANYSFC"; val = "ADPSFC,SFCSHP,ADPUPA,SATWND,PROFLR,MSONET"; },
>
> { key = "ONLYSF"; val = "ADPSFC,SFCSHP"; }
>
> ];
>
>
>
> message_type_map = [
>
> { key = "FM-12 SYNOP"; val = "ADPSFC"; },
>
> { key = "FM-13 SHIP"; val = "SFCSHP"; },
>
> { key = "FM-15 METAR"; val = "ADPSFC"; },
>
> { key = "FM-18 BUOY"; val = "SFCSHP"; },
>
> { key = "FM-281 QSCAT"; val = "ASCATW"; },
>
> { key = "FM-32 PILOT"; val = "ADPUPA"; },
>
> { key = "FM-35 TEMP"; val = "ADPUPA"; },
>
> { key = "FM-88 SATOB"; val = "SATWND"; },
>
> { key = "FM-97 ACARS"; val = "AIRCFT"; }
>
> ];
>
> After executing the Point_stat, the reminding information are as fellow:
>
> WARNING: LittleRHandler::_processObs() -> Storing message type as "*FM*-88_GEOAMV"
> for unexpected report type "*FM*-88 GEOAMV".
> WARNING: LittleRHandler::_processObs() -> Storing message type as "*FM*-88_GEOAMV"
> for unexpected report type "*FM*-88_GEOAMV".
>
> I see, if the header information in little_r format is set to
> FM-88_GEOAMV, it does not meet the requirements of the file format. So how
> do I set it here?
>
> 3) Since METv4.0, the observation data column has been changed to 11 from
> 10 by adding QC flags. Here, I do not know the flag meaning though I set
> them all to 0 signs. Could you please let me know the meanings? Such as 9,
> 2, 3, Na in the tutorial.
>
> The detail information is attached to the letter.
>
> I am looking forward your response at your convenience and Thank you so
> much.
>
> Best regards,
>
> Yu Xin
>
>
>
> At 2018-02-02 05:57:28, "John Halley Gotway" <johnhg at ucar.edu> wrote:
>
> MET Practical Exercises:
> https://dtcenter.org/met/users/support/OnLinePractical/
>
> PDF of slides:
>
> https://dtcenter.org/met/users/support/OnLinePractical/OnLinePractical_218/MET+_Tutorial_Master_final.pdf
>
>
----------------------------------------------------------------
Complete Ticket History
----------------------------------------------------------------
Subject: Fwd: METv7 questions
From: Julie Prestopnik
Time: Tue Jul 31 10:17:29 2018
Hi Yu.
I see you are having some trouble using met-7.0.
For 1) and 2), could you please send me the command that you are
running
that produces the warnings you are receiving? Please include the
location
on cheyenne of any data and config files used in the command. For 3),
could you please tell me which MET tool you are referring to?
Regarding:
The detail information is attached to the letter.
>
Unfortunately, I did not receive anything as an attachment.
Thank you!
Julie
On Mon, Jul 30, 2018 at 8:40 PM John Halley Gotway via RT
<met_help at ucar.edu>
wrote:
>
> Mon Jul 30 20:40:46 2018: Request 86400 was acted upon.
> Transaction: Ticket created by johnhg
> Queue: met_help
> Subject: Fwd: METv7 questions
> Owner: Nobody
> Requestors: johnhg at ucar.edu
> Status: new
> Ticket <URL:
https://rt.rap.ucar.edu/rt/Ticket/Display.html?id=86400 >
>
>
> ---------- Forwarded message ---------
> From: Yu Xin <learnerxy at 163.com>
> Date: Mon, Jul 30, 2018 at 4:15 PM
> Subject: METv7 questions
> To: John Halley Gotway <johnhg at ucar.edu>
>
>
>
> To whom that is concerned,
>
> I have some questions about METv7 to ask.Could you please give me
your
> hands on it? See the below.
>
> I am looking forward to your news and thank you so much.
>
> With my best regards,
>
> Yu
>
>
> 在 2018-07-31 04:22:22，"John Halley Gotway" <johnhg at ucar.edu> 写道：
>
> Hi Yu,
>
> I’m out of the office this week. Please send this message to
> met_help at ucar.edu and hopefully my colleagues can answer your
question.
>
> Thanks
> John
>
> On Mon, Jul 30, 2018 at 1:55 PM Yu Xin <learnerxy at 163.com> wrote:
>
> > Hello John Halley,
> >
> > These days, I have been trying to update our operational METv4.0
to
> > METv7.0, but failed on it. The main problems are as follows up to
now:
> >
> > 1) How should I configure the Config file of precipitation
evaluation? I
> > set it like these referring to the REAME file:
> >
> > fcst = {
> >
> > field = [
> >
> >
> > {
> >
> > name = "APCP";
> >
> > level = [ "A06" ];
> >
> > cat_thresh = [ >=0.1, >=2.5,>=3.8, >=5.0,
>=7.5,>=10.0,>=15.0,
> > >=20.0, >=40.0 ];
> >
> > }
> >
> >
> > ];
> >
> >
> > }
> >
> >
> > obs = fcst;
> >
> >
> >
> > but after executing it, it will remind that the name of APCPA06 is
> > unrecognized, like these:
> > DEBUG 2: Reading data for *APCPA06*.
> >
> > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06* found
> > in file:
> >
> /glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061800
> >
> > DEBUG 2: Reading data for *APCPA06*.
> >
> > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06* found
> > in file:
> >
> /glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061800
> >
> > DEBUG 2: Reading data for *APCPA06*.
> >
> > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06* found
> > in file:
> >
> /glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061806
> >
> > So I don't know how to set the precipitation variable correctly in
the
> > corresponding file in METv7.0.
> >
> > 2) I am puzzled by the SATOB's message type in METv7.0. The
corresponding
> > input file is little_r format and I set it in the config file like
these:
> >
> > fcst = {
> >
> > field = [
> >
> >
> > {
> >
> > name = "WIND";
> >
> > level = [
> >
>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> > ];
> >
> > cat_thresh = [ >0.0 ];
> >
> > },
> >
> >
> > {
> >
> > name = "UGRD";
> >
> > level = [
> >
>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> > ];
> >
> > cat_thresh = [ >0.0 ];
> >
> > },
> >
> >
> > {
> >
> > name = "VGRD";
> >
> > level = [
> >
>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> > ];
> >
> > cat_thresh = [ >0.0 ];
> >
> > },
> >
> >
> > {
> >
> > name = "HGT";
> >
> > level = [
> >
>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> > ];
> >
> > cat_thresh = [ >0.0 ];
> >
> > }
> >
> >
> > ];
> >
> >
> > }
> >
> > obs = fcst;
> >
> > //
> >
> > // Point observation filtering options
> >
> > // May be set separately in each "obs.field" entry
> >
> > //
> >
> > message_type = [ "SATWND" ];
> >
> > sid_exc = [];
> >
> > obs_quality = [];
> >
> > duplicate_flag = NONE;
> >
> > obs_summary = NONE;
> >
> > obs_perc_value = 50;
> >
> >
> > //
> >
> > // Mapping of message type group name to comma-separated list of
values.
> >
> > //
> >
> > message_type_group_map = [
> >
> > { key = "SURFACE"; val = "ADPSFC,SFCSHP,MSONET";
},
> >
> > { key = "ANYAIR"; val = "AIRCAR,AIRCFT";
},
> >
> > { key = "ANYSFC"; val =
"ADPSFC,SFCSHP,ADPUPA,SATWND,PROFLR,MSONET";
> },
> >
> > { key = "ONLYSF"; val = "ADPSFC,SFCSHP";
}
> >
> > ];
> >
> >
> >
> > message_type_map = [
> >
> > { key = "FM-12 SYNOP"; val = "ADPSFC"; },
> >
> > { key = "FM-13 SHIP"; val = "SFCSHP"; },
> >
> > { key = "FM-15 METAR"; val = "ADPSFC"; },
> >
> > { key = "FM-18 BUOY"; val = "SFCSHP"; },
> >
> > { key = "FM-281 QSCAT"; val = "ASCATW"; },
> >
> > { key = "FM-32 PILOT"; val = "ADPUPA"; },
> >
> > { key = "FM-35 TEMP"; val = "ADPUPA"; },
> >
> > { key = "FM-88 SATOB"; val = "SATWND"; },
> >
> > { key = "FM-97 ACARS"; val = "AIRCFT"; }
> >
> > ];
> >
> > After executing the Point_stat, the reminding information are as
fellow:
> >
> > WARNING: LittleRHandler::_processObs() -> Storing message type as
> "*FM*-88_GEOAMV"
> > for unexpected report type "*FM*-88 GEOAMV".
> > WARNING: LittleRHandler::_processObs() -> Storing message type as
> "*FM*-88_GEOAMV"
> > for unexpected report type "*FM*-88_GEOAMV".
> >
> > I see, if the header information in little_r format is set to
> > FM-88_GEOAMV, it does not meet the requirements of the file
format. So
> how
> > do I set it here?
> >
> > 3) Since METv4.0, the observation data column has been changed to
11 from
> > 10 by adding QC flags. Here, I do not know the flag meaning though
I set
> > them all to 0 signs. Could you please let me know the meanings?
Such as
> 9,
> > 2, 3, Na in the tutorial.
> >
> > The detail information is attached to the letter.
> >
> > I am looking forward your response at your convenience and Thank
you so
> > much.
> >
> > Best regards,
> >
> > Yu Xin
> >
> >
> >
> > At 2018-02-02 05:57:28, "John Halley Gotway" <johnhg at ucar.edu>
wrote:
> >
> > MET Practical Exercises:
> > https://dtcenter.org/met/users/support/OnLinePractical/
> >
> > PDF of slides:
> >
> >
>
https://dtcenter.org/met/users/support/OnLinePractical/OnLinePractical_218/MET+_Tutorial_Master_final.pdf
> >
> >
>
>
------------------------------------------------
Subject: Fwd: METv7 questions
From: Julie Prestopnik
Time: Wed Aug 01 10:24:48 2018
Jul 31, 2018, 6:03 PM (16 hours ago)
Hi John.
Thank you for your response soon.
I have given up the Config file of SATOB type and regarded it as a
separate ADPUPA type to process. So this part can pass up to now. But
I will solve it with your help in the future.
I am still puzzled by the Config file of 6-hour accumulated
precipitation. After executing pcp_combine command with subtract
subcommand, it always pops up the message like the below whatever I
try to set key word Level in the corresponding to it:
uxin at cheyenne4:/glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061518> point_stat
wrfrain_d01_acc_6hr.2016061606 /glade/work/yuxin/met/MET-
result/point_obs/netcdf/synop2016061606.nc
/glade/work/yuxin/met/met7.0/config/PointStatConfig_acc6hr -v 2
DEBUG 1: Default Config File:
/glade/p/ral/jntp/MET/MET_releases/7.0/share/met/config/PointStatConfig_default
DEBUG 1: User Config File:
/glade/work/yuxin/met/met7.0/config/PointStatConfig_acc6hr
ERROR :
ERROR : VarInfo::set_level_info_grib() - failed to parse level string
'APCP_06'
So I don't know why my setting level_info_grib() is wrong, and I also
check my NETCDF format observation file by ncdump command. I think the
key words are the same, but it can not work.
Please check my files attached.
Regards,
Yu
On Tue Jul 31 10:17:29 2018, jpresto wrote:
> Hi Yu.
>
> I see you are having some trouble using met-7.0.
>
> For 1) and 2), could you please send me the command that you are
> running
> that produces the warnings you are receiving? Please include the
> location
> on cheyenne of any data and config files used in the command. For
3),
> could you please tell me which MET tool you are referring to?
>
> Regarding:
>
> The detail information is attached to the letter.
> >
>
> Unfortunately, I did not receive anything as an attachment.
>
> Thank you!
>
> Julie
>
>
> On Mon, Jul 30, 2018 at 8:40 PM John Halley Gotway via RT
> <met_help at ucar.edu>
> wrote:
>
> >
> > Mon Jul 30 20:40:46 2018: Request 86400 was acted upon.
> > Transaction: Ticket created by johnhg
> > Queue: met_help
> > Subject: Fwd: METv7 questions
> > Owner: Nobody
> > Requestors: johnhg at ucar.edu
> > Status: new
> > Ticket <URL:
https://rt.rap.ucar.edu/rt/Ticket/Display.html?id=86400
> > >
> >
> >
> > ---------- Forwarded message ---------
> > From: Yu Xin <learnerxy at 163.com>
> > Date: Mon, Jul 30, 2018 at 4:15 PM
> > Subject: METv7 questions
> > To: John Halley Gotway <johnhg at ucar.edu>
> >
> >
> >
> > To whom that is concerned,
> >
> > I have some questions about METv7 to ask.Could you please give me
> > your
> > hands on it? See the below.
> >
> > I am looking forward to your news and thank you so much.
> >
> > With my best regards,
> >
> > Yu
> >
> >
> > 在 2018-07-31 04:22:22，"John Halley Gotway" <johnhg at ucar.edu> 写道：
> >
> > Hi Yu,
> >
> > I’m out of the office this week. Please send this message to
> > met_help at ucar.edu and hopefully my colleagues can answer your
> > question.
> >
> > Thanks
> > John
> >
> > On Mon, Jul 30, 2018 at 1:55 PM Yu Xin <learnerxy at 163.com> wrote:
> >
> > > Hello John Halley,
> > >
> > > These days, I have been trying to update our operational METv4.0
to
> > > METv7.0, but failed on it. The main problems are as follows up
to
> > > now:
> > >
> > > 1) How should I configure the Config file of precipitation
> > > evaluation? I
> > > set it like these referring to the REAME file:
> > >
> > > fcst = {
> > >
> > > field = [
> > >
> > >
> > > {
> > >
> > > name = "APCP";
> > >
> > > level = [ "A06" ];
> > >
> > > cat_thresh = [ >=0.1, >=2.5,>=3.8, >=5.0, >=7.5,>=10.0,>=15.0,
> > > > =20.0, >=40.0 ];
> > >
> > > }
> > >
> > >
> > > ];
> > >
> > >
> > > }
> > >
> > >
> > > obs = fcst;
> > >
> > >
> > >
> > > but after executing it, it will remind that the name of APCPA06
is
> > > unrecognized, like these:
> > > DEBUG 2: Reading data for *APCPA06*.
> > >
> > > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06*
> > > found
> > > in file:
> > >
> > /glade/work/yuxin/met/MET-
> >
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061800
> > >
> > > DEBUG 2: Reading data for *APCPA06*.
> > >
> > > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06*
> > > found
> > > in file:
> > >
> > /glade/work/yuxin/met/MET-
> >
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061800
> > >
> > > DEBUG 2: Reading data for *APCPA06*.
> > >
> > > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06*
> > > found
> > > in file:
> > >
> > /glade/work/yuxin/met/MET-
> >
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061806
> > >
> > > So I don't know how to set the precipitation variable correctly
in
> > > the
> > > corresponding file in METv7.0.
> > >
> > > 2) I am puzzled by the SATOB's message type in METv7.0. The
> > > corresponding
> > > input file is little_r format and I set it in the config file
like
> > > these:
> > >
> > > fcst = {
> > >
> > > field = [
> > >
> > >
> > > {
> > >
> > > name = "WIND";
> > >
> > > level = [
> > >
> >
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> > > ];
> > >
> > > cat_thresh = [ >0.0 ];
> > >
> > > },
> > >
> > >
> > > {
> > >
> > > name = "UGRD";
> > >
> > > level = [
> > >
> >
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> > > ];
> > >
> > > cat_thresh = [ >0.0 ];
> > >
> > > },
> > >
> > >
> > > {
> > >
> > > name = "VGRD";
> > >
> > > level = [
> > >
> >
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> > > ];
> > >
> > > cat_thresh = [ >0.0 ];
> > >
> > > },
> > >
> > >
> > > {
> > >
> > > name = "HGT";
> > >
> > > level = [
> > >
> >
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
> > > ];
> > >
> > > cat_thresh = [ >0.0 ];
> > >
> > > }
> > >
> > >
> > > ];
> > >
> > >
> > > }
> > >
> > > obs = fcst;
> > >
> > > //
> > >
> > > // Point observation filtering options
> > >
> > > // May be set separately in each "obs.field" entry
> > >
> > > //
> > >
> > > message_type = [ "SATWND" ];
> > >
> > > sid_exc = [];
> > >
> > > obs_quality = [];
> > >
> > > duplicate_flag = NONE;
> > >
> > > obs_summary = NONE;
> > >
> > > obs_perc_value = 50;
> > >
> > >
> > > //
> > >
> > > // Mapping of message type group name to comma-separated list of
> > > values.
> > >
> > > //
> > >
> > > message_type_group_map = [
> > >
> > > { key = "SURFACE"; val = "ADPSFC,SFCSHP,MSONET";
},
> > >
> > > { key = "ANYAIR"; val = "AIRCAR,AIRCFT";
},
> > >
> > > { key = "ANYSFC"; val =
> > > "ADPSFC,SFCSHP,ADPUPA,SATWND,PROFLR,MSONET";
> > },
> > >
> > > { key = "ONLYSF"; val = "ADPSFC,SFCSHP"; }
> > >
> > > ];
> > >
> > >
> > >
> > > message_type_map = [
> > >
> > > { key = "FM-12 SYNOP"; val = "ADPSFC"; },
> > >
> > > { key = "FM-13 SHIP"; val = "SFCSHP"; },
> > >
> > > { key = "FM-15 METAR"; val = "ADPSFC"; },
> > >
> > > { key = "FM-18 BUOY"; val = "SFCSHP"; },
> > >
> > > { key = "FM-281 QSCAT"; val = "ASCATW"; },
> > >
> > > { key = "FM-32 PILOT"; val = "ADPUPA"; },
> > >
> > > { key = "FM-35 TEMP"; val = "ADPUPA"; },
> > >
> > > { key = "FM-88 SATOB"; val = "SATWND"; },
> > >
> > > { key = "FM-97 ACARS"; val = "AIRCFT"; }
> > >
> > > ];
> > >
> > > After executing the Point_stat, the reminding information are as
> > > fellow:
> > >
> > > WARNING: LittleRHandler::_processObs() -> Storing message type
as
> > "*FM*-88_GEOAMV"
> > > for unexpected report type "*FM*-88 GEOAMV".
> > > WARNING: LittleRHandler::_processObs() -> Storing message type
as
> > "*FM*-88_GEOAMV"
> > > for unexpected report type "*FM*-88_GEOAMV".
> > >
> > > I see, if the header information in little_r format is set to
> > > FM-88_GEOAMV, it does not meet the requirements of the file
format.
> > > So
> > how
> > > do I set it here?
> > >
> > > 3) Since METv4.0, the observation data column has been changed
to
> > > 11 from
> > > 10 by adding QC flags. Here, I do not know the flag meaning
though
> > > I set
> > > them all to 0 signs. Could you please let me know the meanings?
> > > Such as
> > 9,
> > > 2, 3, Na in the tutorial.
> > >
> > > The detail information is attached to the letter.
> > >
> > > I am looking forward your response at your convenience and Thank
> > > you so
> > > much.
> > >
> > > Best regards,
> > >
> > > Yu Xin
> > >
> > >
> > >
> > > At 2018-02-02 05:57:28, "John Halley Gotway" <johnhg at ucar.edu>
> > > wrote:
> > >
> > > MET Practical Exercises:
> > > https://dtcenter.org/met/users/support/OnLinePractical/
> > >
> > > PDF of slides:
> > >
> > >
> >
https://dtcenter.org/met/users/support/OnLinePractical/OnLinePractical_218/MET+_Tutorial_Master_final.pdf
> > >
> > >
> >
> >
------------------------------------------------
Subject: Fwd: METv7 questions
From: Julie Prestopnik
Time: Wed Aug 01 10:33:50 2018
Hi Yu.
It sounds like you're looking for some clarification on the error
you're getting with pcp_combine.
Could you please send the pcp_combine command that you are running so
that I can try to reproduce the error? I have access to Cheyenne, so
if you could please tell me the location of the files that you are
using with pcp_combine, I would appreciate it.
I'm only in the office for another hour or so and then I am out for
the rest of the week, so if you could please send this information as
soon as possible, I will try to help you before I leave.
Thanks!
Julie
------------------------------------------------
Subject: Fwd: METv7 questions
From: Julie Prestopnik
Time: Wed Aug 01 10:38:57 2018
Actually, perhaps I misunderstood. It looks like you are receiving
that error with point_stat and not pcp_combine. On cheyenne, I copied
over the files and ran your command and I do not see the same
behavior. Below are the commands I executed and the resulting output.
Please check the module that you are loading and see if it is the same
as what I have. Please try rerunning and let me know if you still get
the error.
Thanks!
Julie
cd /glade/u/home/jpresto/met_help/yuxin_20180801
cp /glade/work/yuxin/met/met7.0/config/PointStatConfig_acc6hr .
cp /glade/work/yuxin/met/MET-
result/point_obs/netcdf/synop2016061606.nc .
cp /glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061518/wrfrain_d01_acc_6hr.2016061606
.
module use /glade/p/ral/jntp/MET/MET_releases/modulefiles
module load met/7.0
cheyenne5:jpresto> point_stat wrfrain_d01_acc_6hr.2016061606
synop2016061606.nc PointStatConfig_acc6hr -v 2
DEBUG 1: Default Config File:
/glade/p/ral/jntp/MET/MET_releases/7.0/share/met/config/PointStatConfig_default
DEBUG 1: User Config File: PointStatConfig_acc6hr
GSL_RNG_TYPE=mt19937
GSL_RNG_SEED=299917659
DEBUG 1: Forecast File: wrfrain_d01_acc_6hr.2016061606
DEBUG 1: Observation File: synop2016061606.nc
DEBUG 2:
DEBUG 2:
--------------------------------------------------------------------------------
DEBUG 2:
DEBUG 2: Reading data for APCP_06A06.
DEBUG 2: Processing masking regions.
DEBUG 2: For APCP_06A06 found 1 forecast levels, 0 climatology mean
levels, and 0 climatology standard deviation levels.
DEBUG 2:
DEBUG 2:
--------------------------------------------------------------------------------
DEBUG 2:
DEBUG 2: Searching 43919 observations from 5918 messages.
DEBUG 2:
DEBUG 2:
--------------------------------------------------------------------------------
DEBUG 2:
DEBUG 2: Processing APCP_06A06 versus APCP/A06, for observation type
ADPSFC, over region FULL, for interpolation method NEAREST(1), using
1282 pairs.
DEBUG 2: Computing Categorical Statistics.
DEBUG 2: Computing Multi-Category Statistics.
DEBUG 2: Computing Continuous Statistics.
DEBUG 2: Computing Scalar Partial Sums.
DEBUG 2: Processing APCP_06A06 versus APCP/A06, for observation type
ADPSFC, over region NA, for interpolation method NEAREST(1), using 0
pairs.
DEBUG 2:
DEBUG 2:
--------------------------------------------------------------------------------
DEBUG 2:
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V.stat
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_fho.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_ctc.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_cts.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_mcts.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_cnt.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_sl1l2.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_sal1l2.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_vl1l2.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_val1l2.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_pct.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_pstd.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_pjc.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_prc.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_eclv.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_mpr.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_vcnt.txt
------------------------------------------------
Subject: Fwd: METv7 questions
From: Julie Prestopnik
Time: Wed Aug 01 10:41:52 2018
Hi. I sent two responses via the ticketing system, but I did not
receive
them in my email inbox as I usually do, so I am resending my responses
through email in case you did not receive them. Please be sure to
"Reply
All" to this email so that the response also goes to our ticketing
system.
Thanks,
Julie
RESPONSE #1:
Hi Yu.
It sounds like you're looking for some clarification on the error
you're
getting with pcp_combine.
Could you please send the pcp_combine command that you are running so
that
I can try to reproduce the error? I have access to Cheyenne, so if you
could please tell me the location of the files that you are using with
pcp_combine, I would appreciate it.
I'm only in the office for another hour or so and then I am out for
the
rest of the week, so if you could please send this information as soon
as
possible, I will try to help you before I leave.
Thanks!
Julie
RESPONSE #2:
Actually, perhaps I misunderstood. It looks like you are receiving
that
error with point_stat and not pcp_combine. On cheyenne, I copied over
the
files and ran your command and I do not see the same behavior. Below
are
the commands I executed and the resulting output. Please check the
module
that you are loading and see if it is the same as what I have. Please
try
rerunning and let me know if you still get the error.
Thanks!
Julie
cd /glade/u/home/jpresto/met_help/yuxin_20180801
cp /glade/work/yuxin/met/met7.0/config/PointStatConfig_acc6hr .
cp /glade/work/yuxin/met/MET-
result/point_obs/netcdf/synop2016061606.nc .
cp
/glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061518/wrfrain_d01_acc_6hr.2016061606
.
module use /glade/p/ral/jntp/MET/MET_releases/modulefiles
module load met/7.0
cheyenne5:jpresto> point_stat wrfrain_d01_acc_6hr.2016061606
synop2016061606.nc PointStatConfig_acc6hr -v 2
DEBUG 1: Default Config File:
/glade/p/ral/jntp/MET/MET_releases/7.0/share/met/config/PointStatConfig_default
DEBUG 1: User Config File: PointStatConfig_acc6hr
GSL_RNG_TYPE=mt19937
GSL_RNG_SEED=299917659
DEBUG 1: Forecast File: wrfrain_d01_acc_6hr.2016061606
DEBUG 1: Observation File: synop2016061606.nc
DEBUG 2:
DEBUG 2:
--------------------------------------------------------------------------------
DEBUG 2:
DEBUG 2: Reading data for APCP_06A06.
DEBUG 2: Processing masking regions.
DEBUG 2: For APCP_06A06 found 1 forecast levels, 0 climatology mean
levels,
and 0 climatology standard deviation levels.
DEBUG 2:
DEBUG 2:
--------------------------------------------------------------------------------
DEBUG 2:
DEBUG 2: Searching 43919 observations from 5918 messages.
DEBUG 2:
DEBUG 2:
--------------------------------------------------------------------------------
DEBUG 2:
DEBUG 2: Processing APCP_06A06 versus APCP/A06, for observation type
ADPSFC, over region FULL, for interpolation method NEAREST(1), using
1282
pairs.
DEBUG 2: Computing Categorical Statistics.
DEBUG 2: Computing Multi-Category Statistics.
DEBUG 2: Computing Continuous Statistics.
DEBUG 2: Computing Scalar Partial Sums.
DEBUG 2: Processing APCP_06A06 versus APCP/A06, for observation type
ADPSFC, over region NA, for interpolation method NEAREST(1), using 0
pairs.
DEBUG 2:
DEBUG 2:
--------------------------------------------------------------------------------
DEBUG 2:
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V.stat
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_fho.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_ctc.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_cts.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_mcts.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_cnt.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_sl1l2.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_sal1l2.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_vl1l2.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_val1l2.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_pct.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_pstd.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_pjc.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_prc.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_eclv.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_mpr.txt
DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_vcnt.txt
On Tue, Jul 31, 2018 at 10:17 AM Julie Prestopnik <jpresto at ucar.edu>
wrote:
> Hi Yu.
>
> I see you are having some trouble using met-7.0.
>
> For 1) and 2), could you please send me the command that you are
running
> that produces the warnings you are receiving? Please include the
location
> on cheyenne of any data and config files used in the command. For
3),
> could you please tell me which MET tool you are referring to?
>
> Regarding:
>
> The detail information is attached to the letter.
>>
>
> Unfortunately, I did not receive anything as an attachment.
>
> Thank you!
>
> Julie
>
>
> On Mon, Jul 30, 2018 at 8:40 PM John Halley Gotway via RT <
> met_help at ucar.edu> wrote:
>
>>
>> Mon Jul 30 20:40:46 2018: Request 86400 was acted upon.
>> Transaction: Ticket created by johnhg
>> Queue: met_help
>> Subject: Fwd: METv7 questions
>> Owner: Nobody
>> Requestors: johnhg at ucar.edu
>> Status: new
>> Ticket <URL:
https://rt.rap.ucar.edu/rt/Ticket/Display.html?id=86400 >
>>
>>
>> ---------- Forwarded message ---------
>> From: Yu Xin <learnerxy at 163.com>
>> Date: Mon, Jul 30, 2018 at 4:15 PM
>> Subject: METv7 questions
>> To: John Halley Gotway <johnhg at ucar.edu>
>>
>>
>>
>> To whom that is concerned,
>>
>> I have some questions about METv7 to ask.Could you please give me
your
>> hands on it? See the below.
>>
>> I am looking forward to your news and thank you so much.
>>
>> With my best regards,
>>
>> Yu
>>
>>
>> 在 2018-07-31 04:22:22，"John Halley Gotway" <johnhg at ucar.edu> 写道：
>>
>> Hi Yu,
>>
>> I’m out of the office this week. Please send this message to
>> met_help at ucar.edu and hopefully my colleagues can answer your
question.
>>
>> Thanks
>> John
>>
>> On Mon, Jul 30, 2018 at 1:55 PM Yu Xin <learnerxy at 163.com> wrote:
>>
>> > Hello John Halley,
>> >
>> > These days, I have been trying to update our operational METv4.0
to
>> > METv7.0, but failed on it. The main problems are as follows up to
now:
>> >
>> > 1) How should I configure the Config file of precipitation
evaluation? I
>> > set it like these referring to the REAME file:
>> >
>> > fcst = {
>> >
>> > field = [
>> >
>> >
>> > {
>> >
>> > name = "APCP";
>> >
>> > level = [ "A06" ];
>> >
>> > cat_thresh = [ >=0.1, >=2.5,>=3.8, >=5.0,
>=7.5,>=10.0,>=15.0,
>> > >=20.0, >=40.0 ];
>> >
>> > }
>> >
>> >
>> > ];
>> >
>> >
>> > }
>> >
>> >
>> > obs = fcst;
>> >
>> >
>> >
>> > but after executing it, it will remind that the name of APCPA06
is
>> > unrecognized, like these:
>> > DEBUG 2: Reading data for *APCPA06*.
>> >
>> > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06*
>> found
>> > in file:
>> >
>> /glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061800
>> >
>> > DEBUG 2: Reading data for *APCPA06*.
>> >
>> > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06*
>> found
>> > in file:
>> >
>> /glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061800
>> >
>> > DEBUG 2: Reading data for *APCPA06*.
>> >
>> > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06*
>> found
>> > in file:
>> >
>> /glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061806
>> >
>> > So I don't know how to set the precipitation variable correctly
in the
>> > corresponding file in METv7.0.
>> >
>> > 2) I am puzzled by the SATOB's message type in METv7.0. The
>> corresponding
>> > input file is little_r format and I set it in the config file
like
>> these:
>> >
>> > fcst = {
>> >
>> > field = [
>> >
>> >
>> > {
>> >
>> > name = "WIND";
>> >
>> > level = [
>> >
>>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
>> > ];
>> >
>> > cat_thresh = [ >0.0 ];
>> >
>> > },
>> >
>> >
>> > {
>> >
>> > name = "UGRD";
>> >
>> > level = [
>> >
>>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
>> > ];
>> >
>> > cat_thresh = [ >0.0 ];
>> >
>> > },
>> >
>> >
>> > {
>> >
>> > name = "VGRD";
>> >
>> > level = [
>> >
>>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
>> > ];
>> >
>> > cat_thresh = [ >0.0 ];
>> >
>> > },
>> >
>> >
>> > {
>> >
>> > name = "HGT";
>> >
>> > level = [
>> >
>>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
>> > ];
>> >
>> > cat_thresh = [ >0.0 ];
>> >
>> > }
>> >
>> >
>> > ];
>> >
>> >
>> > }
>> >
>> > obs = fcst;
>> >
>> > //
>> >
>> > // Point observation filtering options
>> >
>> > // May be set separately in each "obs.field" entry
>> >
>> > //
>> >
>> > message_type = [ "SATWND" ];
>> >
>> > sid_exc = [];
>> >
>> > obs_quality = [];
>> >
>> > duplicate_flag = NONE;
>> >
>> > obs_summary = NONE;
>> >
>> > obs_perc_value = 50;
>> >
>> >
>> > //
>> >
>> > // Mapping of message type group name to comma-separated list of
values.
>> >
>> > //
>> >
>> > message_type_group_map = [
>> >
>> > { key = "SURFACE"; val = "ADPSFC,SFCSHP,MSONET";
},
>> >
>> > { key = "ANYAIR"; val = "AIRCAR,AIRCFT";
},
>> >
>> > { key = "ANYSFC"; val =
>> "ADPSFC,SFCSHP,ADPUPA,SATWND,PROFLR,MSONET"; },
>> >
>> > { key = "ONLYSF"; val = "ADPSFC,SFCSHP";
}
>> >
>> > ];
>> >
>> >
>> >
>> > message_type_map = [
>> >
>> > { key = "FM-12 SYNOP"; val = "ADPSFC"; },
>> >
>> > { key = "FM-13 SHIP"; val = "SFCSHP"; },
>> >
>> > { key = "FM-15 METAR"; val = "ADPSFC"; },
>> >
>> > { key = "FM-18 BUOY"; val = "SFCSHP"; },
>> >
>> > { key = "FM-281 QSCAT"; val = "ASCATW"; },
>> >
>> > { key = "FM-32 PILOT"; val = "ADPUPA"; },
>> >
>> > { key = "FM-35 TEMP"; val = "ADPUPA"; },
>> >
>> > { key = "FM-88 SATOB"; val = "SATWND"; },
>> >
>> > { key = "FM-97 ACARS"; val = "AIRCFT"; }
>> >
>> > ];
>> >
>> > After executing the Point_stat, the reminding information are as
fellow:
>> >
>> > WARNING: LittleRHandler::_processObs() -> Storing message type as
>> "*FM*-88_GEOAMV"
>> > for unexpected report type "*FM*-88 GEOAMV".
>> > WARNING: LittleRHandler::_processObs() -> Storing message type as
>> "*FM*-88_GEOAMV"
>> > for unexpected report type "*FM*-88_GEOAMV".
>> >
>> > I see, if the header information in little_r format is set to
>> > FM-88_GEOAMV, it does not meet the requirements of the file
format. So
>> how
>> > do I set it here?
>> >
>> > 3) Since METv4.0, the observation data column has been changed to
11
>> from
>> > 10 by adding QC flags. Here, I do not know the flag meaning
though I set
>> > them all to 0 signs. Could you please let me know the meanings?
Such as
>> 9,
>> > 2, 3, Na in the tutorial.
>> >
>> > The detail information is attached to the letter.
>> >
>> > I am looking forward your response at your convenience and Thank
you so
>> > much.
>> >
>> > Best regards,
>> >
>> > Yu Xin
>> >
>> >
>> >
>> > At 2018-02-02 05:57:28, "John Halley Gotway" <johnhg at ucar.edu>
wrote:
>> >
>> > MET Practical Exercises:
>> > https://dtcenter.org/met/users/support/OnLinePractical/
>> >
>> > PDF of slides:
>> >
>> >
>>
https://dtcenter.org/met/users/support/OnLinePractical/OnLinePractical_218/MET+_Tutorial_Master_final.pdf
>> >
>> >
>>
>>
------------------------------------------------
Subject: Fwd: METv7 questions
From: Julie Prestopnik
Time: Wed Aug 01 11:04:55 2018
HI Julie,
Thank you for your answer soon.
Nomatter how I try the point_stat command like what I told you before,
it can not work. But just now, I set the controlling like this, it can
work now.
fcst = {
censor_thresh = [];
censor_val = [];
cnt_thresh = [ NA ];
cnt_logic = UNION;
wind_thresh = [ NA ];
wind_logic = UNION;
eclv_points = 0.05;
field = [
{
name = "APCP_06";
level = [ "A06" ];
cat_thresh = [ >=0.1, >=2.5,>=3.8, >=5.0, >=7.5,>=10.0,>=15.0,
>=20.0, >=40.0 ];
}
];
}
//obs = fcst;
obs = {
message_type = [ "ADPSFC" ];
field = [
{
name = "APCP";
level = [ "A06" ];
cat_thresh = [ >=0.1, >=2.5,>=3.8, >=5.0, >=7.5,>=10.0,>=15.0,
>=20.0, >=40.0 ];
}
];
}
I wonder why the result is different underlying the same command and
test data.
Thank you so much. and I have some questions about SATOB test to ask
you in another email.
Byebye
Best regards,
Yu
------------------------------------------------
Subject: Fwd: METv7 questions
From: Julie Prestopnik
Time: Wed Aug 01 11:08:55 2018
Hi Yu.
It looks like I had grabbed the file that you had already modified,
changing the name from
name = "APCP";
to
name = "APCP_06";
which explains why it worked for me.
APCP_06 is indeed the name in the file, so it needs to match in your
config
file. Once you made that change, MET was able to find that field.
You mentioned that you had some questions about SATOB to ask in
another
email. Please submit those questions in a new email to
met_help at ucar.edu
so that whomever is in the office can help. I am about to leave for
the
rest of the week, so if you send it to my email address, you will not
receive a prompt response.
Thanks,
Julie
On Wed, Aug 1, 2018 at 10:41 AM Julie Prestopnik <jpresto at ucar.edu>
wrote:
> Hi. I sent two responses via the ticketing system, but I did not
receive
> them in my email inbox as I usually do, so I am resending my
responses
> through email in case you did not receive them. Please be sure to
"Reply
> All" to this email so that the response also goes to our ticketing
system.
>
> Thanks,
> Julie
>
> RESPONSE #1:
> Hi Yu.
>
> It sounds like you're looking for some clarification on the error
you're
> getting with pcp_combine.
>
> Could you please send the pcp_combine command that you are running
so that
> I can try to reproduce the error? I have access to Cheyenne, so if
you
> could please tell me the location of the files that you are using
with
> pcp_combine, I would appreciate it.
>
> I'm only in the office for another hour or so and then I am out for
the
> rest of the week, so if you could please send this information as
soon as
> possible, I will try to help you before I leave.
>
> Thanks!
>
> Julie
>
> RESPONSE #2:
> Actually, perhaps I misunderstood. It looks like you are receiving
that
> error with point_stat and not pcp_combine. On cheyenne, I copied
over the
> files and ran your command and I do not see the same behavior. Below
are
> the commands I executed and the resulting output. Please check the
module
> that you are loading and see if it is the same as what I have.
Please try
> rerunning and let me know if you still get the error.
>
> Thanks!
>
> Julie
>
> cd /glade/u/home/jpresto/met_help/yuxin_20180801
> cp /glade/work/yuxin/met/met7.0/config/PointStatConfig_acc6hr .
> cp /glade/work/yuxin/met/MET-
result/point_obs/netcdf/synop2016061606.nc .
> cp
> /glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061518/wrfrain_d01_acc_6hr.2016061606
> .
>
> module use /glade/p/ral/jntp/MET/MET_releases/modulefiles
> module load met/7.0
>
> cheyenne5:jpresto> point_stat wrfrain_d01_acc_6hr.2016061606
> synop2016061606.nc PointStatConfig_acc6hr -v 2
> DEBUG 1: Default Config File:
>
/glade/p/ral/jntp/MET/MET_releases/7.0/share/met/config/PointStatConfig_default
> DEBUG 1: User Config File: PointStatConfig_acc6hr
> GSL_RNG_TYPE=mt19937
> GSL_RNG_SEED=299917659
> DEBUG 1: Forecast File: wrfrain_d01_acc_6hr.2016061606
> DEBUG 1: Observation File: synop2016061606.nc
> DEBUG 2:
> DEBUG 2:
>
--------------------------------------------------------------------------------
> DEBUG 2:
> DEBUG 2: Reading data for APCP_06A06.
> DEBUG 2: Processing masking regions.
> DEBUG 2: For APCP_06A06 found 1 forecast levels, 0 climatology mean
> levels, and 0 climatology standard deviation levels.
> DEBUG 2:
> DEBUG 2:
>
--------------------------------------------------------------------------------
> DEBUG 2:
> DEBUG 2: Searching 43919 observations from 5918 messages.
> DEBUG 2:
> DEBUG 2:
>
--------------------------------------------------------------------------------
> DEBUG 2:
> DEBUG 2: Processing APCP_06A06 versus APCP/A06, for observation type
> ADPSFC, over region FULL, for interpolation method NEAREST(1), using
1282
> pairs.
> DEBUG 2: Computing Categorical Statistics.
> DEBUG 2: Computing Multi-Category Statistics.
> DEBUG 2: Computing Continuous Statistics.
> DEBUG 2: Computing Scalar Partial Sums.
> DEBUG 2: Processing APCP_06A06 versus APCP/A06, for observation type
> ADPSFC, over region NA, for interpolation method NEAREST(1), using 0
pairs.
> DEBUG 2:
> DEBUG 2:
>
--------------------------------------------------------------------------------
> DEBUG 2:
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V.stat
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_fho.txt
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_ctc.txt
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_cts.txt
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_mcts.txt
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_cnt.txt
> DEBUG 1: Output file:
./point_stat_120000L_20160616_060000V_sl1l2.txt
> DEBUG 1: Output file:
./point_stat_120000L_20160616_060000V_sal1l2.txt
> DEBUG 1: Output file:
./point_stat_120000L_20160616_060000V_vl1l2.txt
> DEBUG 1: Output file:
./point_stat_120000L_20160616_060000V_val1l2.txt
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_pct.txt
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_pstd.txt
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_pjc.txt
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_prc.txt
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_eclv.txt
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_mpr.txt
> DEBUG 1: Output file: ./point_stat_120000L_20160616_060000V_vcnt.txt
>
> On Tue, Jul 31, 2018 at 10:17 AM Julie Prestopnik <jpresto at ucar.edu>
> wrote:
>
>> Hi Yu.
>>
>> I see you are having some trouble using met-7.0.
>>
>> For 1) and 2), could you please send me the command that you are
running
>> that produces the warnings you are receiving? Please include the
location
>> on cheyenne of any data and config files used in the command. For
3),
>> could you please tell me which MET tool you are referring to?
>>
>> Regarding:
>>
>> The detail information is attached to the letter.
>>>
>>
>> Unfortunately, I did not receive anything as an attachment.
>>
>> Thank you!
>>
>> Julie
>>
>>
>> On Mon, Jul 30, 2018 at 8:40 PM John Halley Gotway via RT <
>> met_help at ucar.edu> wrote:
>>
>>>
>>> Mon Jul 30 20:40:46 2018: Request 86400 was acted upon.
>>> Transaction: Ticket created by johnhg
>>> Queue: met_help
>>> Subject: Fwd: METv7 questions
>>> Owner: Nobody
>>> Requestors: johnhg at ucar.edu
>>> Status: new
>>> Ticket <URL:
https://rt.rap.ucar.edu/rt/Ticket/Display.html?id=86400 >
>>>
>>>
>>> ---------- Forwarded message ---------
>>> From: Yu Xin <learnerxy at 163.com>
>>> Date: Mon, Jul 30, 2018 at 4:15 PM
>>> Subject: METv7 questions
>>> To: John Halley Gotway <johnhg at ucar.edu>
>>>
>>>
>>>
>>> To whom that is concerned,
>>>
>>> I have some questions about METv7 to ask.Could you please give me
your
>>> hands on it? See the below.
>>>
>>> I am looking forward to your news and thank you so much.
>>>
>>> With my best regards,
>>>
>>> Yu
>>>
>>>
>>> 在 2018-07-31 04:22:22，"John Halley Gotway" <johnhg at ucar.edu> 写道：
>>>
>>> Hi Yu,
>>>
>>> I’m out of the office this week. Please send this message to
>>> met_help at ucar.edu and hopefully my colleagues can answer your
question.
>>>
>>> Thanks
>>> John
>>>
>>> On Mon, Jul 30, 2018 at 1:55 PM Yu Xin <learnerxy at 163.com> wrote:
>>>
>>> > Hello John Halley,
>>> >
>>> > These days, I have been trying to update our operational METv4.0
to
>>> > METv7.0, but failed on it. The main problems are as follows up
to now:
>>> >
>>> > 1) How should I configure the Config file of precipitation
evaluation?
>>> I
>>> > set it like these referring to the REAME file:
>>> >
>>> > fcst = {
>>> >
>>> > field = [
>>> >
>>> >
>>> > {
>>> >
>>> > name = "APCP";
>>> >
>>> > level = [ "A06" ];
>>> >
>>> > cat_thresh = [ >=0.1, >=2.5,>=3.8, >=5.0,
>=7.5,>=10.0,>=15.0,
>>> > >=20.0, >=40.0 ];
>>> >
>>> > }
>>> >
>>> >
>>> > ];
>>> >
>>> >
>>> > }
>>> >
>>> >
>>> > obs = fcst;
>>> >
>>> >
>>> >
>>> > but after executing it, it will remind that the name of APCPA06
is
>>> > unrecognized, like these:
>>> > DEBUG 2: Reading data for *APCPA06*.
>>> >
>>> > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06*
>>> found
>>> > in file:
>>> >
>>> /glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061800
>>> >
>>> > DEBUG 2: Reading data for *APCPA06*.
>>> >
>>> > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06*
>>> found
>>> > in file:
>>> >
>>> /glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061800
>>> >
>>> > DEBUG 2: Reading data for *APCPA06*.
>>> >
>>> > WARNING: process_fcst_climo_files() -> no fields matching
*APCPA06*
>>> found
>>> > in file:
>>> >
>>> /glade/work/yuxin/met/MET-
result/fcst/wrfprd/radar_result_1/2016061718/wrfrain_d01_acc_6hr.2016061806
>>> >
>>> > So I don't know how to set the precipitation variable correctly
in the
>>> > corresponding file in METv7.0.
>>> >
>>> > 2) I am puzzled by the SATOB's message type in METv7.0. The
>>> corresponding
>>> > input file is little_r format and I set it in the config file
like
>>> these:
>>> >
>>> > fcst = {
>>> >
>>> > field = [
>>> >
>>> >
>>> > {
>>> >
>>> > name = "WIND";
>>> >
>>> > level = [
>>> >
>>>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
>>> > ];
>>> >
>>> > cat_thresh = [ >0.0 ];
>>> >
>>> > },
>>> >
>>> >
>>> > {
>>> >
>>> > name = "UGRD";
>>> >
>>> > level = [
>>> >
>>>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
>>> > ];
>>> >
>>> > cat_thresh = [ >0.0 ];
>>> >
>>> > },
>>> >
>>> >
>>> > {
>>> >
>>> > name = "VGRD";
>>> >
>>> > level = [
>>> >
>>>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
>>> > ];
>>> >
>>> > cat_thresh = [ >0.0 ];
>>> >
>>> > },
>>> >
>>> >
>>> > {
>>> >
>>> > name = "HGT";
>>> >
>>> > level = [
>>> >
>>>
"P925","P850","P700","P600","P500","P400","P300","P250","P200","P150","P100","P50"
>>> > ];
>>> >
>>> > cat_thresh = [ >0.0 ];
>>> >
>>> > }
>>> >
>>> >
>>> > ];
>>> >
>>> >
>>> > }
>>> >
>>> > obs = fcst;
>>> >
>>> > //
>>> >
>>> > // Point observation filtering options
>>> >
>>> > // May be set separately in each "obs.field" entry
>>> >
>>> > //
>>> >
>>> > message_type = [ "SATWND" ];
>>> >
>>> > sid_exc = [];
>>> >
>>> > obs_quality = [];
>>> >
>>> > duplicate_flag = NONE;
>>> >
>>> > obs_summary = NONE;
>>> >
>>> > obs_perc_value = 50;
>>> >
>>> >
>>> > //
>>> >
>>> > // Mapping of message type group name to comma-separated list of
>>> values.
>>> >
>>> > //
>>> >
>>> > message_type_group_map = [
>>> >
>>> > { key = "SURFACE"; val = "ADPSFC,SFCSHP,MSONET";
},
>>> >
>>> > { key = "ANYAIR"; val = "AIRCAR,AIRCFT";
},
>>> >
>>> > { key = "ANYSFC"; val =
>>> "ADPSFC,SFCSHP,ADPUPA,SATWND,PROFLR,MSONET"; },
>>> >
>>> > { key = "ONLYSF"; val = "ADPSFC,SFCSHP";
}
>>> >
>>> > ];
>>> >
>>> >
>>> >
>>> > message_type_map = [
>>> >
>>> > { key = "FM-12 SYNOP"; val = "ADPSFC"; },
>>> >
>>> > { key = "FM-13 SHIP"; val = "SFCSHP"; },
>>> >
>>> > { key = "FM-15 METAR"; val = "ADPSFC"; },
>>> >
>>> > { key = "FM-18 BUOY"; val = "SFCSHP"; },
>>> >
>>> > { key = "FM-281 QSCAT"; val = "ASCATW"; },
>>> >
>>> > { key = "FM-32 PILOT"; val = "ADPUPA"; },
>>> >
>>> > { key = "FM-35 TEMP"; val = "ADPUPA"; },
>>> >
>>> > { key = "FM-88 SATOB"; val = "SATWND"; },
>>> >
>>> > { key = "FM-97 ACARS"; val = "AIRCFT"; }
>>> >
>>> > ];
>>> >
>>> > After executing the Point_stat, the reminding information are as
>>> fellow:
>>> >
>>> > WARNING: LittleRHandler::_processObs() -> Storing message type
as
>>> "*FM*-88_GEOAMV"
>>> > for unexpected report type "*FM*-88 GEOAMV".
>>> > WARNING: LittleRHandler::_processObs() -> Storing message type
as
>>> "*FM*-88_GEOAMV"
>>> > for unexpected report type "*FM*-88_GEOAMV".
>>> >
>>> > I see, if the header information in little_r format is set to
>>> > FM-88_GEOAMV, it does not meet the requirements of the file
format. So
>>> how
>>> > do I set it here?
>>> >
>>> > 3) Since METv4.0, the observation data column has been changed
to 11
>>> from
>>> > 10 by adding QC flags. Here, I do not know the flag meaning
though I
>>> set
>>> > them all to 0 signs. Could you please let me know the meanings?
Such
>>> as 9,
>>> > 2, 3, Na in the tutorial.
>>> >
>>> > The detail information is attached to the letter.
>>> >
>>> > I am looking forward your response at your convenience and Thank
you so
>>> > much.
>>> >
>>> > Best regards,
>>> >
>>> > Yu Xin
>>> >
>>> >
>>> >
>>> > At 2018-02-02 05:57:28, "John Halley Gotway" <johnhg at ucar.edu>
wrote:
>>> >
>>> > MET Practical Exercises:
>>> > https://dtcenter.org/met/users/support/OnLinePractical/
>>> >
>>> > PDF of slides:
>>> >
>>> >
>>>
https://dtcenter.org/met/users/support/OnLinePractical/OnLinePractical_218/MET+_Tutorial_Master_final.pdf
>>> >
>>> >
>>>
>>>
------------------------------------------------
More information about the Met_help
mailing list